How much chlorine to add to your pool: chart, formula and examples
Rule of thumb: 12.8 fl oz of 10% liquid chlorine raises free chlorine by 1 ppm in 10,000 gallons. Multiply by how many ppm you need and by your gallons ÷ 10,000.
"Add a splash" isn't a dose. The amount of chlorine you need depends on three numbers: how much you want to raise free chlorine (FC), how big your pool is, and how strong your chlorine is. Here's how to work it out.
Step 1: Decide your target FC
Your target depends on your stabilizer (CYA) level. The CDC's minimum for a home pool is 1 ppm without stabilizer and 2 ppm with it. A common approach is to keep FC at about 7.5% of CYA or more:
| CYA (ppm) | Minimum FC | Target FC | Shock (SLAM) FC |
|---|---|---|---|
| 0 | 1.0 | 2.0 | 10 |
| 20 | 1.5 | 3.0 | 10 |
| 30 | 2.2 | 4.0 | 12 |
| 40 | 3.0 | 5.0 | 16 |
| 50 | 3.8 | 6.0 | 20 |
| 60 | 4.5 | 7.0 | 24 |
| 70 | 5.2 | 8.0 | 28 |
| 80 | 6.0 | 9.0 | 32 |
| 90 | 6.8 | 10.0 | 36 |
Based on the TroubleFreePool FC/CYA chart: minimum ≈ 7.5% of CYA, target ≈ CYA ÷ 10 + 1 (the low end of their target range), shock ≈ 40% of CYA, with floors of 1, 2 and 10 ppm. Rounded, so values can differ from their chart by a fraction of a ppm.
Step 2: Find your product in the chart
Each amount below raises FC by about 1 ppm in 10,000 gallons:
| Chlorine product | Amount to raise FC by 1 ppm in 10,000 gallons |
|---|---|
| Liquid chlorine 12.5% | 10.2 fl oz |
| Liquid chlorine 10% | 12.8 fl oz |
| Bleach 8.25% | 15.5 fl oz |
| Bleach 6% | 21.3 fl oz |
| Cal-hypo 73% | 1.8 oz (weight) |
| Cal-hypo 65% | 2.1 oz (weight) |
| Dichlor 56% | 2.4 oz (weight) |
| Trichlor 90% | 1.5 oz (weight) |
Liquid percentages are "trade percent" (available chlorine by volume), which is how pool chlorine is usually labeled. 10% liquid: 1 gallon (128 fl oz) adds about 10 ppm to 10,000 gallons. Solid products: amount = 1.34 oz ÷ (% available chlorine ÷ 100).
Step 3: Do the math
Dose = (amount per 1 ppm) × (ppm you need) × (your gallons ÷ 10,000)
Example 1: 15,000-gallon pool, 10% liquid chlorine
CYA is 40, so the target FC is about 5. The strip reads 1. You need to raise FC by 4 ppm.
12.8 × 4 × 1.5 = 77 fl oz (about 9.6 cups, a bit over half a gallon).
Example 2: 20,000-gallon pool, 6% bleach
You need to raise FC by 2 ppm.
21.3 × 2 × 2 = 85 fl oz (about two-thirds of a gallon).
Example 3: 10,000-gallon pool, 73% cal-hypo
You need to raise FC by 5 ppm.
1.8 × 5 × 1 = 9 oz by weight. Cal-hypo also adds a little calcium to the water.
Skip the math
Enter your pool size, your chlorine and your strip readings. The free calculator gives you the dose in fl oz, cups or pounds, plus your FC target for your CYA.
Open the free pool calculatorWhich chlorine should you use?
- Liquid chlorine or plain bleach adds only chlorine (and a little salt). It's the easiest to dose precisely. It loses strength as it ages, especially in heat, so fresher is stronger.
- Cal-hypo adds calcium hardness along with chlorine. Fine if your calcium is low; a problem if it's already high.
- Dichlor and trichlor add stabilizer (CYA) every time you use them. Roughly, each 1 ppm of FC from dichlor adds about 0.9 ppm CYA, and from trichlor about 0.6 ppm. Over a season that adds up, and higher CYA means you need more FC.
Shocking (SLAM)
If combined chlorine is above 0.5 ppm, or the water is cloudy or green, raise FC to shock level (about 40% of CYA, see the chart) and hold it there until combined chlorine is 0.5 or lower and the water is clear. That usually takes repeated doses, and a drop test kit reads high chlorine much better than strips.
Safety
- Add chlorine to the pool with the pump running, one chemical at a time.
- Never mix chlorine with acid or with other chlorine types. That can release toxic gas or cause a fire.
- Follow the product label. It's the legal instruction for that product.
- Retest after the water has circulated before adding more.
FAQ
How much liquid chlorine do I add to raise FC by 1 ppm?
About 12.8 fl oz of 10% liquid chlorine (or 10.2 fl oz of 12.5%) per 10,000 gallons.
How much bleach do I add to my pool?
About 21.3 fl oz of 6% bleach raises free chlorine by 1 ppm in 10,000 gallons. Use plain, unscented bleach only.
How much chlorine do I need for a 10,000-gallon pool?
It depends on how far you need to raise FC. With 10% liquid chlorine it's 12.8 fl oz per ppm, so going from 1 to 4 ppm takes about 38 fl oz.
What should free chlorine be in a pool?
At least 1 ppm without stabilizer and 2 ppm with it (CDC). Many owners keep FC at about 7.5% of their CYA or more.
Sources
- CDC: Home Pool and Hot Tub Water Treatment and Testing
- TroubleFreePool: The Free Chlorine and Cyanuric Acid Relationship
- TroubleFreePool wiki: CYA/Chlorine relationship (FC/CYA chart)
- CDC: 2024 Model Aquatic Health Code, 5th edition (code language, PDF)
- Example EPA-registered 10% chlorinating liquid label (13 fl oz per 10,000 gal for 1 ppm)