How to raise alkalinity in a pool
- Raise total alkalinity (TA) with baking soda (sodium bicarbonate). It's the same product as the pool-store "alkalinity increaser," usually cheaper at a warehouse store.
- 1.4 lb of baking soda raises TA by about 10 ppm in 10,000 gallons.
- Aim for roughly 60–120 ppm. Pools with a salt cell or lots of aeration often do best near 60–80.
Total alkalinity is the water's pH buffer. When it's too low, pH bounces around with every rainstorm or chlorine dose and can crash low, which is hard on plaster, metal parts and swimmers' eyes. Raising it is one of the easiest fixes in pool care.
What total alkalinity does
TA mostly measures bicarbonate in the water. Bicarbonate soaks up acid, which keeps pH from dropping suddenly. That's useful, but more isn't better: high TA makes pH drift upward and increases scaling risk (see how to lower pH). The goal is a moderate level.
What level to aim for
| Source | TA range |
|---|---|
| Common home-pool target | About 60–120 ppm |
| TroubleFreePool, liquid chlorine pools | Ideal 60–80 ppm (acceptable from about 50) |
| 2024 Model Aquatic Health Code (public pools) | 60–180 ppm |
Sources: TroubleFreePool recommended levels, CDC MAHC. If your pool uses trichlor tabs, which are acidic, a TA near the higher end helps counter the constant pH drop.
Signs your alkalinity is low
- The TA pad on your strip reads under about 60–80 ppm.
- pH swings or drops quickly, especially after rain or when using trichlor.
- Etching or roughness on plaster, or corrosion on metal ladders and heater parts.
- Stinging eyes even when chlorine looks fine.
How much baking soda to add
Baking soda is pure chemistry, so the dose is predictable: about 1.4 lb raises TA by 10 ppm in 10,000 gallons.
| Raise TA by | 10,000 gal | 15,000 gal | 20,000 gal | 25,000 gal |
|---|---|---|---|---|
| 10 ppm | 1.4 lb | 2.1 lb | 2.8 lb | 3.5 lb |
| 20 ppm | 2.8 lb | 4.2 lb | 5.6 lb | 7.0 lb |
| 30 ppm | 4.2 lb | 6.3 lb | 8.4 lb | 10.5 lb |
| 40 ppm | 5.6 lb | 8.4 lb | 11.2 lb | 14.0 lb |
| 50 ppm | 7.0 lb | 10.5 lb | 14.0 lb | 17.5 lb |
A standard box of baking soda is 1 lb; warehouse bags are often 12–13.5 lb. If you don't know your volume, use the pool volume calculator first.
Skip the math
Enter your pool size, your chlorine and your strip readings. The free calculator gives you the dose in fl oz, cups or pounds, plus your FC target for your CYA.
Open the free pool calculatorStep by step
- Test TA and pH. If pH is also low, baking soda will nudge it up a little. If pH is fine, that's OK too: baking soda has only a small effect on pH.
- Add no more than about 10–20 lb at once in a typical residential pool, broadcasting it across the deep end with the pump running. Big doses can cloud the water temporarily.
- Brush any powder that settles on the floor.
- Circulate for at least 6 hours, then retest before adding more.
- Adjust pH last, once TA is where you want it.
Baking soda vs. soda ash
Both raise alkalinity, but very differently. Baking soda (sodium bicarbonate) raises TA a lot and pH only a little. Soda ash (sodium carbonate) raises pH a lot and TA too. If pH is in range and TA is low, use baking soda. If both are low, start with baking soda and use soda ash only if pH is still low afterward.
Why alkalinity drops
- Acid additions. Every dose of muriatic or dry acid lowers TA as well as pH.
- Trichlor tablets are acidic and wear down TA over time.
- Rain dilutes the water and is slightly acidic.
- Water replacement with low-alkalinity fill water.
Common mistakes
- Chasing pH with baking soda. Baking soda barely moves pH. If TA is fine and pH is low, use soda ash or aeration instead.
- Adding everything at once. Large doses can cloud the water and overshoot. Add in steps, circulate, retest.
- Ignoring CYA in the TA reading. Stabilizer adds a little to the TA test result (roughly a third of the CYA level), so pools with high CYA have a bit less real buffering than the strip suggests.
- Testing right after adding chemicals. Wait at least a few hours with the pump running before retesting.
- Using the wrong volume. If doses keep missing, check your pool size with the volume calculator.
Can alkalinity be too high?
Yes. Above about 120 ppm in a residential pool, pH tends to climb steadily and you'll add acid often. The fix is the acid-and-aerate routine TroubleFreePool describes in how to lower TA: lower pH to about 7.0–7.2 with acid, aerate until it rises to 7.4–7.6, and repeat.
FAQ
How much baking soda raises alkalinity 10 ppm?
About 1.4 lb per 10,000 gallons. For 20,000 gallons, about 2.8 lb.
Is baking soda the same as alkalinity increaser?
Yes. Pool-store alkalinity increaser is sodium bicarbonate, the same chemical as household baking soda.
Can I swim after adding baking soda?
Generally yes, once it has dissolved and mixed, but check the product label. Baking soda is mild.
Should I adjust alkalinity or pH first?
Alkalinity first, then pH. TA changes affect pH, so fix the buffer before fine-tuning pH.