How to lower pH in a pool
- Lower pH with muriatic acid (hydrochloric acid) or dry acid (sodium bisulfate). Aim for about 7.4–7.6; the CDC range for pools is 7.2–7.8.
- How much acid you need depends on your total alkalinity (TA). In 10,000 gallons at TA 80–100, dropping from 7.8 to 7.4 takes roughly 8–11 fl oz of 31.45% muriatic acid.
- If pH keeps climbing, the usual cause is high TA plus aeration (waterfalls, spillovers, salt cells). Lowering TA slows the drift.
pH is the second number most pool owners fight with, right after chlorine. High pH isn't dangerous on its own, but it makes chlorine much less effective and pushes the water toward cloudy, scaly conditions. Here's how to bring it down safely and how much acid to use.
Why high pH is a problem
- Weaker chlorine. The CDC notes that chlorine works less well as pH rises, especially above 8.0. At high pH, more of your chlorine is in its weaker form.
- Scale and cloudiness. High pH, especially with high calcium and alkalinity, makes calcium carbonate come out of solution as scale on tile, in the heater and on salt cells, and can cloud the water (TroubleFreePool on scaling).
- Eye and skin irritation for swimmers.
What pH to aim for
The CDC recommends keeping pool pH between 7.2 and 7.8. Many owners target 7.4–7.6 because it's comfortable and gives you room before you need to act. If you use a salt chlorine generator or have lots of aeration, pH will drift up between adjustments, so a target near the low end means fewer corrections.
A test strip's pH pad usually reads in steps of about 0.2 to 0.4, so if your strip says 8.0 or higher, take action. Our color chart guide explains how to read the pad.
Muriatic acid vs. dry acid
| Muriatic acid (31.45% or ~14.5%) | Dry acid (sodium bisulfate) | |
|---|---|---|
| Cost | Usually cheapest per dose | More expensive |
| Handling | Liquid with strong fumes, needs care | Granular, easier to store and measure |
| Side effects | Adds a little salt (chloride) | Adds sulfates, which can build up over seasons |
Both lower pH and TA by the same chemistry. Use whichever you're comfortable handling, and always follow the product label.
How much acid to add
The same amount of acid moves pH much further in a low-alkalinity pool than in a high one, because alkalinity is the water's buffer. Here are starting estimates for 10,000 gallons:
| Total alkalinity | pH 7.8 → 7.6 | pH 7.8 → 7.4 |
|---|---|---|
| 60 ppm | 2 fl oz | 6 fl oz |
| 80 ppm | 3 fl oz | 8 fl oz |
| 100 ppm | 4 fl oz | 11 fl oz |
| 120 ppm | 5 fl oz | 13 fl oz |
| 150 ppm | 7 fl oz | 17 fl oz |
Starting estimates for 10,000 gallons of water with CYA 30 ppm, using 31.45% muriatic acid. Calculated from carbonate chemistry; borates, higher CYA and fresh plaster add buffering, so add about three quarters, circulate, retest, then finish.
For other pool sizes, scale linearly: a 20,000-gallon pool needs twice as much, a 5,000-gallon pool half. Lowering total alkalinity itself is more predictable: about 25.6 fl oz (a bit under a quart) of 31.45% muriatic acid removes 10 ppm of TA from 10,000 gallons. Half-strength acid needs roughly twice the volume.
Skip the math
Enter your pool size, your chlorine and your strip readings. The free calculator gives you the dose in fl oz, cups or pounds, plus your FC target for your CYA.
Open the free pool calculatorStep by step
- Test pH and TA with a fresh strip or kit. Know your pool volume (use the volume calculator if you're not sure).
- Measure about three quarters of the dose in a clean plastic container used only for acid.
- With the pump running, pour slowly into the deep end in front of a return jet, low over the water to avoid splashing. Add acid to water, never water to acid.
- Circulate at least 30–60 minutes, then retest. Add the rest if needed.
- Wait before adding chlorine. Add acid and chlorine at different times and places, and never mix them: together they release chlorine gas. TroubleFreePool suggests waiting between chemical additions so each one mixes in.
Safety
- Wear chemical-splash goggles and gloves, and work upwind.
- Store acid away from chlorine, ideally in a separate, ventilated area. Acid fumes corrode metal.
- Keep everyone out of the pool until the acid has mixed, usually 30 minutes with the pump running.
Why pH keeps rising, and how to slow it
Pool water constantly loses carbon dioxide to the air, and that raises pH. Anything that agitates the water speeds this up: waterfalls, spa spillovers, fountains, heavy swimming and salt cells. The more alkalinity there is, the more COâ‚‚ there is to lose.
- Lower TA toward 60–80 ppm if your pH rises fast. TroubleFreePool's acid-and-aerate method lowers TA without crashing pH: lower pH to about 7.0–7.2 with acid, aerate until it climbs back to 7.4–7.6, repeat.
- Reduce aeration when you don't need it.
- Consider borates. TroubleFreePool notes that 30–50 ppm of borates can slow pH rise (their guide).
- Check your chlorine type. Liquid chlorine and cal-hypo raise pH slightly as they're used; trichlor tabs lower it (and add CYA).
What if pH is too low?
Below 7.2, water can irritate eyes and slowly corrode metal and etch plaster. Raise pH with soda ash (sodium carbonate), or with aeration if TA is also high. If TA is low, raise it first with baking soda, which nudges pH up a little too. See how to raise alkalinity.
FAQ
How much muriatic acid do I add to lower pH?
It depends on volume and total alkalinity. As a starting estimate, dropping pH from 7.8 to 7.4 in 10,000 gallons takes roughly 8–11 fl oz of 31.45% muriatic acid at TA 80–100 ppm. Add three quarters, circulate, retest, then finish.
How long after adding acid can I swim?
Usually about 30 minutes with the pump running, once the acid has mixed. Follow the product label and retest first.
Can I lower pH without lowering alkalinity?
Not with acid: acid always lowers both. To lower pH while keeping TA, use COâ‚‚ injection. To lower TA while keeping pH in range, use the acid-and-aerate method.
Why does my pool pH keep going up?
Pools lose CO₂ to the air, which raises pH. High alkalinity, aeration, spillovers and salt chlorine generators speed it up. Lowering TA toward 60–80 ppm slows the rise.
Sources
- CDC: Home Pool and Hot Tub Water Treatment and Testing
- CDC: 2024 Model Aquatic Health Code, 5th edition (code language, PDF)
- TroubleFreePool: What Are My Ideal Pool Levels?
- TroubleFreePool: How to lower total alkalinity
- TroubleFreePool: Calcium scaling
- TroubleFreePool: How long to wait between adding pool chemicals
- TroubleFreePool: Borates in pools (slowing pH rise)