Pool test strip color chart: what each pad means and the ideal ranges

Updated November 20, 2026 ยท 6 min read ยท by the Pool Strip Reader team

The short version: FC 1โ€“3 ppm or more (scale it with CYA), pH 7.2โ€“7.8, total alkalinity about 60โ€“120 ppm, calcium about 200โ€“400 ppm (plaster), CYA about 30โ€“50 ppm. Colors vary by brand, so always read against the chart on your own bottle. This page tells you what the numbers mean.

Typical pad colors, low to high

These are the color families most combo strips use. Exact shades differ from brand to brand, which is why your bottle's chart is the only one to match against.

PadLow โ†’ high (typical)What the color is telling you
Free chlorineWhite means little or no chlorine. Darker pink to purple means more.
Total chlorineSame scale. Darker than the free chlorine pad means combined chlorine is present.
pHYellow/orange is low (acidic). Red/magenta is high.
Total alkalinityYellow is low. Green to teal is higher.
Total hardnessOften shifts from blue toward purple or red as calcium rises.
Cyanuric acid (CYA)Often light tan/orange when low, moving toward pink or purple when high.

Illustration only. Not a substitute for your strip's chart.

Ideal ranges for each pad

PadWhat it measuresTypical target for a home poolNotes
Free chlorine (FC)Chlorine available to sanitizeAt least 1 ppm with no stabilizer, at least 2 ppm with stabilizer (CDC). Scale with CYA (see below).The most important pad.
Total chlorine (TC)Free + combined chlorineClose to FCTC minus FC = combined chlorine (CC).
Combined chlorine (CC)Used-up chlorine (chloramines)0.5 ppm or lessHigher usually means it's time to shock. The 2024 MAHC (a public-pool code) acts above 0.4 ppm.
pHAcidity7.2โ€“7.8 (CDC allows 7.0โ€“7.8). Many owners aim for 7.4โ€“7.6.Chlorine works less well as pH rises, especially above 8.0 (CDC).
Total alkalinity (TA)pH bufferAbout 60โ€“120 ppmThe 2024 MAHC allows 60โ€“180 ppm for public pools.
Calcium hardness (CH)Dissolved calciumAbout 200โ€“400 ppm for plaster; vinyl and fiberglass can run lowerToo low can etch plaster; too high can scale.
Cyanuric acid (CYA)Stabilizer (sun protection for chlorine)About 30โ€“50 ppm (higher, often 60โ€“80, with a salt chlorinator)The 2024 MAHC caps public pools at 90 ppm. More CYA means you need more FC.
SaltSalt chlorinator pools onlyWhatever your chlorinator's manual says (often around 3,000โ€“3,500 ppm)Most combo strips don't measure salt; salt uses separate strips.

Free chlorine depends on your CYA

This is the part most charts leave out. Stabilizer (CYA) protects chlorine from the sun, but it also holds some of it back, so the same FC reading does less work in a stabilized pool. That's why the CDC's minimum doubles from 1 ppm to 2 ppm when stabilizer is present. A widely used rule of thumb from the TroubleFreePool community keeps FC at roughly 7.5% of CYA or more:

CYA (ppm)Minimum FCTarget FCShock (SLAM) FC
01.02.010
201.53.010
302.24.012
403.05.016
503.86.020
604.57.024
705.28.028
806.09.032
906.810.036

Based on the TroubleFreePool FC/CYA chart: minimum โ‰ˆ 7.5% of CYA, target โ‰ˆ CYA รท 10 + 1 (the low end of their target range), shock โ‰ˆ 40% of CYA, with floors of 1, 2 and 10 ppm. Rounded, so values can differ from their chart by a fraction of a ppm.

Skip the math

Enter your pool size, your chlorine and your strip readings. The free calculator gives you the dose in fl oz, cups or pounds, plus your FC target for your CYA.

Open the free pool calculator

What to do when a pad is off

ReadingWhat it usually meansCommon fix
FC lowChlorine is being used up faster than it's addedAdd chlorine (how much)
CC above 0.5Chloramines building upRaise FC to shock level and hold it until CC drops
pH high (above 7.8)Common with fresh plaster, salt chlorinators, aeration, or high TAMuriatic acid or dry acid, a little at a time
pH low (below 7.2)Often from acid overdose or trichlor tabsAeration, or soda ash / borax
TA lowpH swings easilyBaking soda
CH low (plaster)Water may etch plasterCalcium chloride
CYA lowSun burns off chlorine fastStabilizer (cyanuric acid)
CYA very highChlorine is held back; needs very high FCPartial drain and refill (CYA doesn't break down easily)

Always add one chemical at a time, follow the product label, and retest before adding more.

FAQ

What color should my pool test strip be?

It depends on the brand. In general you want the free chlorine pad in the light-to-medium pink range (about 1โ€“3 ppm or more, depending on CYA) and the pH pad around the middle of its scale (7.2โ€“7.8). Match against the chart on your bottle.

What is the ideal pH for a pool?

7.2 to 7.8. CDC guidance allows 7.0 to 7.8, and many owners aim for 7.4 to 7.6.

What should cyanuric acid be in a pool?

About 30โ€“50 ppm for most chlorine pools, often 60โ€“80 ppm with a salt chlorinator. More CYA means you need more free chlorine.

What does it mean if total chlorine is higher than free chlorine?

The difference is combined chlorine (chloramines). Above about 0.5 ppm, it's usually time to shock.

Sources

  1. CDC: Home Pool and Hot Tub Water Treatment and Testing
  2. CDC: 2024 Model Aquatic Health Code, 5th edition (code language, PDF)
  3. TroubleFreePool: The Free Chlorine and Cyanuric Acid Relationship
  4. TroubleFreePool wiki: CYA/Chlorine relationship (FC/CYA chart)
  5. TroubleFreePool: Pool School

Want this for every test, automatically?

Pool Strip Reader logs every strip and gives you exact doses for your pool and the chlorine you bought. We sell no chemicals. Join the list for the beta and the launch-day price.

One email when the beta opens, one at launch. No spam. Unsubscribe anytime by emailing [email protected].