Cyanuric acid (pool stabilizer): the complete guide

Updated November 20, 2026 · 7 min read · by the Pool Strip Reader team
  • Cyanuric acid (CYA, "stabilizer" or "conditioner") shields chlorine from sunlight. Without it, outdoor pools can lose most of their chlorine in a few hours of sun.
  • The trade-off: the more CYA, the more free chlorine you need. A common rule is minimum FC ≈ 7.5% of CYA.
  • Typical targets: 30–50 ppm with liquid chlorine, 60–80 ppm with a salt cell. The only practical way to lower CYA is replacing water.

Cyanuric acid is the most misunderstood number on a pool test strip. It's essential for outdoor pools, but because it doesn't break down, it quietly builds up, and high CYA is a common hidden reason for green or cloudy water even when the strip shows chlorine.

What CYA does

Sunlight's UV rays destroy free chlorine. CYA binds to part of the chlorine and releases it as it's used, which protects it from UV. The cost is that chlorine bound to CYA isn't an active sanitizer, so as CYA rises, a given FC reading does less work. That's why TroubleFreePool and others express chlorine targets relative to CYA (TroubleFreePool's explanation).

Your chlorine target depends on CYA

CYA (ppm)Minimum FCTarget FCShock (SLAM) FC
01.02.010
201.53.010
302.24.012
403.05.016
503.86.020
604.57.024
705.28.028
806.09.032
906.810.036

Based on the TroubleFreePool FC/CYA chart: minimum ≈ 7.5% of CYA, target ≈ CYA ÷ 10 + 1 (the low end of their target range), shock ≈ 40% of CYA, with floors of 1, 2 and 10 ppm. Rounded, so values can differ from their chart by a fraction of a ppm.

So a pool at 80 ppm CYA needs FC around 6–9 ppm to stay safe from algae, while a pool at 30 ppm can run at 3–4. The CDC recommends at least 2 ppm FC in pools that use stabilizer, and the 2024 Model Aquatic Health Code caps CYA at 90 ppm for public pools (MAHC).

What CYA level should you keep?

PoolTypical CYA target
Outdoor, liquid chlorine or bleachAbout 30–50 ppm
Salt water chlorine generatorAbout 60–80 ppm (TroubleFreePool suggests 70–80)
Indoor or fully shadedLow or none (0–20 ppm)
Public pools (MAHC limit)No more than 90 ppm

Salt pools run higher because the cell produces chlorine slowly and continuously, so more UV protection lets the cell work less. See salt water pool chemistry.

How CYA builds up

CYA doesn't evaporate or get used up quickly; it leaves mainly with water through splash-out, backwashing, leaks and rain overflow. Stabilized chlorine products add it every time you use them:

A season of tabs can push CYA from 40 to over 100 ppm. Liquid chlorine, bleach and cal-hypo add no CYA, which is why many owners switch to them once CYA is where they want it.

How to raise CYA

Add stabilizer (granular cyanuric acid) per the label. About 13 oz by weight raises CYA by roughly 10 ppm in 10,000 gallons. It dissolves slowly: put it in a sock in the skimmer basket or a bucket of warm water, and wait several days of circulation before retesting. Don't backwash during that time.

How to lower high CYA

There's no reliable chemical that removes CYA in a typical home pool. The practical fix is dilution: drain part of the water and refill.

Current CYATarget CYAReplace about
60 ppm40 ppm33%
80 ppm50 ppm38%
100 ppm50 ppm50%
120 ppm50 ppm58%
150 ppm50 ppm67%

Formula: percent to replace = (1 − target ÷ current) × 100. Replace in stages if you can't drain that much at once (for example, vinyl liners shouldn't be drained too low; check with your installer). TroubleFreePool also describes a no-drain water exchange where you add fresh water while pumping out the same amount.

Until you can dilute, keep FC at the right level for your actual CYA. That's often enough to keep the water clear, just more expensive in chlorine.

Skip the math

Enter your pool size, your chlorine and your strip readings. The free calculator gives you the dose in fl oz, cups or pounds, plus your FC target for your CYA.

Open the free pool calculator

Test strips and CYA

CYA pads are among the hardest strip pads to read, and color differences above about 100 ppm are small. If your strip suggests very high CYA, confirm with a turbidity (cloudiness) test before draining. Our strip reading guide covers technique.

FAQ

What is the ideal cyanuric acid level?

About 30–50 ppm for outdoor pools using liquid chlorine, and about 60–80 ppm with a salt chlorine generator. Indoor pools need little or none.

How do I lower cyanuric acid without draining?

There's no reliable chemical method for home pools. Dilution (draining and refilling, or a no-drain water exchange) is the standard fix. Meanwhile, keep FC high enough for your CYA level.

Is cyanuric acid the same as stabilizer?

Yes. Stabilizer and conditioner are product names for cyanuric acid (CYA).

How much chlorine do I need with high CYA?

As a rule of thumb, minimum FC is about 7.5% of CYA and a good target is about CYA ÷ 10 + 1. At 80 ppm CYA, that's about 6 ppm minimum and 9 ppm target.

Sources

  1. CDC: Home Pool and Hot Tub Water Treatment and Testing
  2. CDC: 2024 Model Aquatic Health Code, 5th edition (code language, PDF)
  3. TroubleFreePool: The Free Chlorine and Cyanuric Acid Relationship
  4. TroubleFreePool wiki: CYA/Chlorine relationship (FC/CYA chart)
  5. TroubleFreePool: What Are My Ideal Pool Levels?
  6. TroubleFreePool: Salt water pool (SWG) water balance tips

Want this for every test, automatically?

Pool Strip Reader logs every strip and gives you exact doses for your pool and the chlorine you bought. We sell no chemicals. Join the list for the beta and the launch-day price.

One email when the beta opens, one at launch. No spam. Unsubscribe anytime by emailing [email protected].