Salt water pool chemistry: ideal levels and how to keep them
- A salt water pool is a chlorine pool: a salt chlorine generator (SWG) makes chlorine from dissolved salt. You still need to test free chlorine, pH, alkalinity, CYA and salt.
- Typical targets: salt per your cell's manual (often around 3,000โ3,500 ppm), CYA 60โ80 ppm, TA about 60โ80 ppm, pH 7.4โ7.6.
- Salt pools tend to have rising pH. Lower TA and less aeration help.
Salt pools feel softer and need less hands-on chlorine dosing, but they're not maintenance-free. The chemistry is the same as any chlorine pool, with a few twists. Here's what to keep where, and why.
How a salt pool works
The water holds a low level of salt, about a tenth as salty as the ocean. Inside the cell, electrolysis turns chloride into chlorine, which sanitizes the pool, reacts, and eventually turns back into chloride. So the salt isn't used up; you only add more when water leaves through splash-out, backwashing or rain overflow (TroubleFreePool on SWGs).
Ideal levels for a salt water pool
| Reading | Typical target | Notes |
|---|---|---|
| Salt | Per your cell's manual, often ~3,000โ3,500 ppm | Aim a bit above the middle of the manufacturer's range |
| Free chlorine | Based on CYA (see below) | Set cell output and pump run time to hold it |
| pH | 7.4โ7.6 (CDC range 7.2โ7.8) | Tends to rise; check twice a week |
| Total alkalinity | About 60โ80 ppm | Lower TA slows pH rise |
| CYA (stabilizer) | 60โ80 ppm | TroubleFreePool suggests 70โ80 for SWGs |
| Calcium hardness | About 200โ400 ppm for plaster | High CH with high pH scales the cell |
Sources: TroubleFreePool SWG water balance, CDC. Your cell's manual overrides general advice on salt.
Chlorine in a salt pool
Because CYA runs higher in a salt pool, free chlorine needs to run higher too:
| CYA (ppm) | Minimum FC | Target FC | Shock (SLAM) FC |
|---|---|---|---|
| 0 | 1.0 | 2.0 | 10 |
| 20 | 1.5 | 3.0 | 10 |
| 30 | 2.2 | 4.0 | 12 |
| 40 | 3.0 | 5.0 | 16 |
| 50 | 3.8 | 6.0 | 20 |
| 60 | 4.5 | 7.0 | 24 |
| 70 | 5.2 | 8.0 | 28 |
| 80 | 6.0 | 9.0 | 32 |
| 90 | 6.8 | 10.0 | 36 |
Based on the TroubleFreePool FC/CYA chart: minimum โ 7.5% of CYA, target โ CYA รท 10 + 1 (the low end of their target range), shock โ 40% of CYA, with floors of 1, 2 and 10 ppm. Rounded, so values can differ from their chart by a fraction of a ppm.
At CYA 70, a good target is around 8 ppm. If FC is low, increase the cell's output percentage or run the pump longer. If FC drops fast for no obvious reason, check the cell for scale and confirm salt is in range.
How much salt to add
Water weighs about 8.34 lb per gallon, so 1 ppm of salt in 10,000 gallons is about 0.083 lb. Pounds of pool salt needed to raise salt by:
| Raise salt by | 10,000 gal | 15,000 gal | 20,000 gal | 30,000 gal |
|---|---|---|---|---|
| 500 ppm | 42 lb | 63 lb | 83 lb | 125 lb |
| 1,000 ppm | 83 lb | 125 lb | 167 lb | 250 lb |
| 2,000 ppm | 167 lb | 250 lb | 334 lb | 500 lb |
| 3,000 ppm | 250 lb | 375 lb | 500 lb | 751 lb |
A 40-lb bag raises salt by about 480 ppm in 10,000 gallons, or about 200 ppm in 24,000 gallons, the same math TroubleFreePool uses. Turn the cell off while adding salt, pour it in the shallow end, brush until dissolved, and run the pump 24 hours before retesting. Add about 75% of the calculated amount first, because pool volume estimates are often off. Not sure of your volume? Use the pool volume calculator.
Most combo test strips don't measure salt. Use dedicated salt strips or a salt test kit, and compare with your cell's display.
Skip the math
Enter your pool size, your chlorine and your strip readings. The free calculator gives you the dose in fl oz, cups or pounds, plus your FC target for your CYA.
Open the free pool calculatorWhy pH rises in salt pools
The cell produces hydrogen gas bubbles that aerate the water and drive off COโ, which pushes pH up. Waterfalls and spa spillovers do the same. To slow it:
- Keep TA around 60โ80 ppm (see how to lower pH for the acid-and-aerate method).
- Add acid in small, regular doses rather than big corrections.
- Consider borates at 30โ50 ppm, which TroubleFreePool notes can slow pH rise and reduce scale risk on the cell.
Protect the cell from scale
Scale forms on the cell plates when pH, calcium and alkalinity are high. Keep pH from drifting above 7.8, keep TA modest, and inspect the cell a few times a season. Clean it only as the manufacturer directs.
Do salt pools still need shock?
If FC stays at target for your CYA, routine shocking isn't needed. If algae appears or the water clouds, raise FC to shock level with liquid chlorine rather than waiting for the cell, which is too slow for that job. See cloudy pool water and the green pool troubleshooter.
FAQ
What should the salt level be in a salt water pool?
Whatever your chlorine generator's manual specifies, often around 3,000โ3,500 ppm. Aim a little above the middle of the manufacturer's range.
What CYA level is best for a salt water pool?
About 60โ80 ppm. TroubleFreePool suggests 70โ80 so the cell can produce less chlorine and last longer.
Why does pH keep rising in my salt water pool?
The cell's hydrogen bubbles and any waterfalls aerate the water and drive off COโ, which raises pH. Keeping alkalinity around 60โ80 ppm slows the rise.
How much salt do I need for a 10,000-gallon pool?
About 83 lb to raise salt by 1,000 ppm. A 40-lb bag raises it about 480 ppm.
Sources
- CDC: Home Pool and Hot Tub Water Treatment and Testing
- TroubleFreePool: Salt water chlorine generators
- TroubleFreePool: Salt water pool (SWG) water balance tips
- TroubleFreePool: The Free Chlorine and Cyanuric Acid Relationship
- TroubleFreePool: What Are My Ideal Pool Levels?
- TroubleFreePool: Borates in pools (slowing pH rise)
- TroubleFreePool: Calcium scaling