Cloudy pool water: causes and how to fix it
- The most common cause of cloudy water is not enough free chlorine for your stabilizer level, which lets an algae bloom start before it turns green.
- Next most common: high pH or alkalinity (calcium clouding) and a filter that isn't keeping up.
- Test first, fix chemistry, then run the filter 24 hours a day until it clears.
Cloudy water is your pool telling you something is off. Swimming in water where you can't see the main drain is a safety risk, because you can't see someone in trouble below the surface. The good news is that a test strip plus a look at your filter usually points straight to the cause.
Start with a test
Test free chlorine (FC), pH, total alkalinity (TA), calcium hardness (CH) and cyanuric acid (CYA). Compare to the ranges below, which come from our test strip color chart guide.
| Pad | What it measures | Typical target for a home pool | Notes |
|---|---|---|---|
| Free chlorine (FC) | Chlorine available to sanitize | At least 1 ppm with no stabilizer, at least 2 ppm with stabilizer (CDC). Scale with CYA (see below). | The most important pad. |
| Total chlorine (TC) | Free + combined chlorine | Close to FC | TC minus FC = combined chlorine (CC). |
| Combined chlorine (CC) | Used-up chlorine (chloramines) | 0.5 ppm or less | Higher usually means it's time to shock. The 2024 MAHC (a public-pool code) acts above 0.4 ppm. |
| pH | Acidity | 7.2–7.8 (CDC allows 7.0–7.8). Many owners aim for 7.4–7.6. | Chlorine works less well as pH rises, especially above 8.0 (CDC). |
| Total alkalinity (TA) | pH buffer | About 60–120 ppm | The 2024 MAHC allows 60–180 ppm for public pools. |
| Calcium hardness (CH) | Dissolved calcium | About 200–400 ppm for plaster; vinyl and fiberglass can run lower | Too low can etch plaster; too high can scale. |
| Cyanuric acid (CYA) | Stabilizer (sun protection for chlorine) | About 30–50 ppm (higher, often 60–80, with a salt chlorinator) | The 2024 MAHC caps public pools at 90 ppm. More CYA means you need more FC. |
| Salt | Salt chlorinator pools only | Whatever your chlorinator's manual says (often around 3,000–3,500 ppm) | Most combo strips don't measure salt; salt uses separate strips. |
The 7 most common causes
1. Low free chlorine (early algae)
If FC is below the minimum for your CYA level, algae and bacteria start to grow. Early on this looks like dull or hazy water, before any green appears. Check your FC against the FC/CYA table below. This is the cause most of the time.
| CYA (ppm) | Minimum FC | Target FC | Shock (SLAM) FC |
|---|---|---|---|
| 0 | 1.0 | 2.0 | 10 |
| 20 | 1.5 | 3.0 | 10 |
| 30 | 2.2 | 4.0 | 12 |
| 40 | 3.0 | 5.0 | 16 |
| 50 | 3.8 | 6.0 | 20 |
| 60 | 4.5 | 7.0 | 24 |
| 70 | 5.2 | 8.0 | 28 |
| 80 | 6.0 | 9.0 | 32 |
| 90 | 6.8 | 10.0 | 36 |
Based on the TroubleFreePool FC/CYA chart: minimum ≈ 7.5% of CYA, target ≈ CYA ÷ 10 + 1 (the low end of their target range), shock ≈ 40% of CYA, with floors of 1, 2 and 10 ppm. Rounded, so values can differ from their chart by a fraction of a ppm.
Fix: raise FC to shock level for your CYA and hold it there until the water clears, a process TroubleFreePool calls SLAM. Our guide on how much chlorine to add has the doses.
2. High pH, alkalinity or calcium
When pH, TA and calcium are all high, calcium carbonate can come out of solution as a fine white haze, often after adding cal-hypo shock or soda ash. Fix: lower pH to about 7.2–7.4 with acid and keep it there; the haze usually dissolves. See how to lower pH.
3. Poor filtration
A dirty, worn or undersized filter, or not running the pump long enough, leaves fine particles in the water. Signs: pressure much higher than the clean reading, weak return flow, or cloudiness that persists with good chemistry. Fix: clean or backwash the filter (TroubleFreePool's filter guide), check sand or cartridge age, and run the pump 24/7 until clear.
4. A heavy bather load or a party
Sunscreen, sweat and body oils use up chlorine fast and add particles. Fix: test right after heavy use, top up FC, and run the filter longer.
5. Rain, dust or pollen
Storms wash in dust, debris and phosphates, and dilute chlorine and alkalinity. Fix: skim, brush, retest, and raise FC.
6. Fresh fill water or new plaster
New water can carry minerals or metals, and new plaster releases calcium dust for weeks. Fix: brush daily and keep pH in range. If the water has a color tint, read about metals in our green pool troubleshooter.
7. Dead algae after a shock
After a successful shock, dead algae turns the water gray-white and cloudy. That's progress. Fix: keep FC at shock level, brush, and let the filter work. Cleaning a cartridge or backwashing more often speeds it up.
Pool turning green?
Answer four quick questions and get the likely cause and a step-by-step fix.
Open the green pool troubleshooterHow to clear cloudy water, step by step
- Test and write down every reading.
- Fix pH first if it's above 7.8: chlorine works much better at 7.2–7.6.
- Raise free chlorine to your target or, if you suspect algae, to shock level for your CYA.
- Brush walls and floor and vacuum debris.
- Run the pump 24 hours a day and clean the filter whenever pressure rises 8–10 psi above clean.
- Retest twice a day until the water is clear and FC holds overnight. TroubleFreePool's overnight chlorine loss test confirms that nothing is still consuming chlorine.
Most pools clear in one to three days once chemistry and filtration are right.
What about clarifiers and flocculants?
Clarifiers clump fine particles so the filter can catch them; flocculants drop them to the floor for vacuuming to waste. They can help with filtration-related cloudiness, but they don't fix low chlorine or high pH, and they can clog cartridge filters. Treat the cause first.
FAQ
Why is my pool cloudy but chlorine is fine?
Check that FC is high enough for your CYA level, not just above 1 ppm. If it is, look at pH, alkalinity and calcium (calcium clouding) and at your filter.
How long does it take to clear a cloudy pool?
Usually one to three days once chlorine and pH are right and the filter runs 24 hours a day. Heavy algae can take longer.
Is it safe to swim in a cloudy pool?
No. If you can't see the bottom at the deepest point, you can't see someone in trouble. Wait until the water is clear.
Does shock fix cloudy water?
If the cause is low chlorine or early algae, yes: raising FC to shock level and holding it there clears it. Shock won't fix calcium clouding or a bad filter.
Sources
- CDC: Home Pool and Hot Tub Water Treatment and Testing
- CDC: 2024 Model Aquatic Health Code, 5th edition (code language, PDF)
- TroubleFreePool: The Free Chlorine and Cyanuric Acid Relationship
- TroubleFreePool: SLAM (Shock Level And Maintain)
- TroubleFreePool: Maintenance and cleaning of pool filters
- TroubleFreePool: Perform the overnight chlorine loss test (OCLT)
- TroubleFreePool: Calcium scaling
- TroubleFreePool: What Are My Ideal Pool Levels?