How to read pool test strips (and what to do with the numbers)
- Dip one strip elbow-deep, away from the return jets, for the time on your bottle.
- Hold it flat, and read each pad at the time the label says, in daylight but not direct sun.
- Compare to the chart on your own bottle. Brands use different colors.
- Then act on the numbers: free chlorine and pH first.
Test strips are the fastest way to check a pool, and they're good enough for routine checks if you use them the right way. Most "my strips are wrong" problems come from three things: reading too late, wet or old strips, and comparing against the wrong chart.
What you need
- A bottle of strips that hasn't expired (the date is on the bottle)
- Dry hands
- Daylight, or a bright white light
Step by step
- Take one strip with dry fingers and close the bottle right away. Humidity ruins strips, and a damp strip gives low or blotchy readings.
- Sample in the right spot. Dip about elbow-deep (around 18 inches), away from return jets, skimmers and the spot where you add chemicals. Surface water and jet water aren't representative.
- Dip for the time on your label, usually a second or two, then pull it straight out. Don't swirl it unless your brand says to.
- Hold it flat, pads up. If you tilt it, colors can bleed from one pad into the next. Many labels say to shake off excess water once. Don't blot the pads.
- Read at the right time. Each pad keeps developing. Most brands give a window (often around 15 seconds), and some read free chlorine almost immediately. Reading late is the most common mistake: colors usually keep darkening.
- Compare in good light. Use daylight in the shade or a bright white light, and hold the strip right next to the chart on the bottle. If a color falls between two blocks, pick the value in between.
- Write it down. One reading is a snapshot. A log shows trends, like chlorine dropping faster on hot weeks.
Skip the math
Enter your pool size, your chlorine and your strip readings. The free calculator gives you the dose in fl oz, cups or pounds, plus your FC target for your CYA.
Open the free pool calculatorWhat each pad means
A typical 6-in-1 strip has free chlorine, total chlorine (or bromine), pH, total alkalinity, total hardness and cyanuric acid (CYA). Here are the usual targets for a home pool:
| Pad | What it measures | Typical target for a home pool | Notes |
|---|---|---|---|
| Free chlorine (FC) | Chlorine available to sanitize | At least 1 ppm with no stabilizer, at least 2 ppm with stabilizer (CDC). Scale with CYA (see below). | The most important pad. |
| Total chlorine (TC) | Free + combined chlorine | Close to FC | TC minus FC = combined chlorine (CC). |
| Combined chlorine (CC) | Used-up chlorine (chloramines) | 0.5 ppm or less | Higher usually means it's time to shock. The 2024 MAHC (a public-pool code) acts above 0.4 ppm. |
| pH | Acidity | 7.2–7.8 (CDC allows 7.0–7.8). Many owners aim for 7.4–7.6. | Chlorine works less well as pH rises, especially above 8.0 (CDC). |
| Total alkalinity (TA) | pH buffer | About 60–120 ppm | The 2024 MAHC allows 60–180 ppm for public pools. |
| Calcium hardness (CH) | Dissolved calcium | About 200–400 ppm for plaster; vinyl and fiberglass can run lower | Too low can etch plaster; too high can scale. |
| Cyanuric acid (CYA) | Stabilizer (sun protection for chlorine) | About 30–50 ppm (higher, often 60–80, with a salt chlorinator) | The 2024 MAHC caps public pools at 90 ppm. More CYA means you need more FC. |
| Salt | Salt chlorinator pools only | Whatever your chlorinator's manual says (often around 3,000–3,500 ppm) | Most combo strips don't measure salt; salt uses separate strips. |
For the full chart with typical colors, see our pool test strip color chart.
Mistakes that make strips read wrong
- Old or humid strips. If a fresh strip's pads look discolored before you dip it, the bottle is spent.
- Reading too late. Set a timer on your phone.
- Very high chlorine. At very high levels (above about 10 ppm), chlorine can bleach DPD-type tests and read falsely low, as the CDC notes for DPD kits. If the chlorine pad looks oddly pale right after you shocked, use a drop kit or wait and retest.
- Using the wrong chart. Colors are not standardized between brands.
How accurate are test strips?
The CDC says strips are less accurate than a DPD test kit. For everyday checks that's fine. When precision matters (shocking a green pool, chasing a stubborn problem, or setting CYA), a drop-based kit is worth it. Many experienced pool owners, including the TroubleFreePool community, use a FAS-DPD drop test for chlorine for that reason.
What to do with the numbers
- Free chlorine first. If it's below the minimum for your CYA, add chlorine. Here's how much chlorine to add.
- Then pH. Above 7.8, lower it with acid. Below 7.2, raise it.
- Then the slow movers: alkalinity, calcium and CYA. These change over days or weeks, not hours.
- One chemical at a time. Never mix chemicals, follow the label, let the pump circulate, and retest before adding more.
FAQ
How long do you leave a pool test strip in the water?
Usually a second or two. Follow the time on your bottle, because brands differ.
When should I read a pool test strip?
At the time your label says, often within about 15 seconds. Colors keep changing, so reading late gives wrong results.
Why are my pool test strips not changing color?
The most common causes are expired or humid strips, or very high chlorine bleaching the pad. Try a fresh bottle or a drop test kit.
Are pool test strips accurate?
They're fine for routine checks, but the CDC notes they're less accurate than a DPD test kit.